Detailed Description

A captivatingly beautiful paint used to create unusual and enchanting “movement”. It is a water-based paint for interiors, featuring exclusive luminous sandy reflections. SABULADOR SOFT can be used to create exclusive and elegant environments in line with new decorative trends, regardless of whether the overall style is modern or classic. SABULADOR SOFT is a very high-quality paint as it is breathable, washable and may be painted over with any other water-based paint. CHARACTERISTICS: To create the colours displayed in the catalogue, mix the SABULADOR SOFT Col. SILVER 100 or Col. GOLD 200 with the corresponding amount of COLORI’ colouring paste. Alternatively, the VALCLONE paint-mixing system may be used to achieve the desired colour. APPLICATION OF SABULADOR SOFT: 1) Brushstroke Effect: apply SABULADOR SOFT using the PV 09 Brush and work in all directions. Allow to dry for about 2 hours at 20°C, then apply a second coat using the same technique. 2) Streaked Effect: apply SABULADOR SOFT using the PV 95 Roller and work in all directions; on the last stroke, move in a vertical direction from top to bottom. Go over the product while it is still wet using the PV 88 or PV 89 Spatula, moving from top to bottom and vice-versa to leave streaks which are as straight as possible. Allow to dry for about 2 hours at 20°C, then apply a second coat using the same Roller and Spatula techniques. APPLICATION OF THE BASE COAT: Old Surfaces. Remove old non-adhering and peeling paint and wash using water and a suitable soap product. Next, apply a coat of PRIMART 600 diluted 50% with water as a fixative. After approximately 4 hours at 20°C, apply a second coat of PRIMART 600 diluted 20 - 30% with water. If, however, the surfaces are clean and not peeling, apply a single coat of PRIMART 600 diluted 15 - 20% with water. After 4 hours at 20°C, proceed with the application of SABULADOR SOFT. New Surfaces. Use a filler to repair the surface. When dry, sand the surface then apply a coat of PRIMART 600 diluted 15 - 20% with water. After 4 hours at 20°C, proceed with the application of SABULADOR SOFT. TECHNICAL DATA: Dilution: SABULADOR SOFT is ready to use, PRIMART 600 should be diluted 15 - 20% with water. Coverage: for SABULADOR SOFT, approximately 1 litre per 10 - 12 square metres for Brushstroke effect and approximately 1 litre per 9 - 10 square metres for Streaked effect; for PRIMART 600, approximately 1 litre per 10 - 12 square metres. Packaging: SABULADOR SOFT comes in 1 - 2.5 - 5 litre containers, in either SILVER 100, GOLD 200 or ALUMINIUM 300 colours; PRIMART 600 is available in 1 - 2.5 - 5 litre containers; COLORI’ comes in 80 and 480 ml packs. Application temperature: between +5°C and +30°C. Drying: in a non-dusty environment for 1 hour at 20°C. Dry after 3 - 4 hours at 20°C. Hardens after 24 hours, depending on the temperature of the room. Appearance of the product: opalescent semi-gloss. Strength: when hardening is complete, a breathable film develops which offers good resistance to knocks and normal abrasion. Washability: washable with water and ordinary detergents 15 days after application. Equipment cleaning: soap and water. Storage: make sure the tin is tightly closed, even after use, and stored at a temperature no lower than +10°C and no higher than +30°C. Stability: approximately 2 years. SAFETY INSTRUCTIONS: Avoid direct contact with the skin. Protect eyes and face. In the event of contact, rinse immediately and thoroughly with water and consult a doctor. Equipment must not be washed in watercourses, drains etc. USER ADVICE: The above information is both correct and accurate. However, considering that the conditions in which the products are used are not under our control, we will not be held liable for any recommendations or advice given. We recommend that the complete cycle is tested on a small wall first in order to ensure it is a success, after which the rest of the decoration procedure may be continued (check the decorative effects regularly as you proceed). This is because SABULADOR SOFT consists of natural products and special resins which react to moisture, heat, ventilation and the application method. Each job will therefore acquire its own unique character. The shades can vary from those shown in the catalogue by 20% to 30%, and also between one batch and another. All the material should therefore be mixed in a large container before the application process is started, in order to avoid differences in colour once the product has been applied.